Do you want to clean the underside of your mower? If so, then I have a perfect guideline for you. Just stay with us and keep reading.
You know due to regular mowing, grass clippings, and debris attached to the underneath of the mower deck, it creates a cake-like layer in the bottom parts of the lawnmower deck.
It actually creates a problem at the spinning of the mower blade. The mower blade gets stuck at the cake-like layer and isn’t able to cut the grasses properly.
I guess you face the same issue. That’s why you want to clean the underside of your mower. Right? No worries!
In this article, you will get a proper guideline on how to clean the underside of a lawnmower.
So, why late? Let’s clean it.
In this content you’ll learn:
An Effective Guide To Clean The Underside Of A Lawnmower
At first, you will get the guidelines for your push mower, and right after that, you will get the guidelines for your riding mower also. Note that you must be more careful if you want to clean the underside of your riding mower.
How To Clean The Underside Of A Push Mower
Before going to the main fact, you will need to gather the necessary tools to clean the underside of a lawnmower. Let’s see what you will need to complete the task perfectly.
Required tools:
- A tarp
- An oil pan
- A garden water hosepipe with sprayer
- A socket wrench
- A wire cleaning brush
- Lubricant oil
- Rubber made hand gloves
- Goggles
Now it’s time to clean the underneath of the mower deck. Follow the steps set out below to perform the entire task conveniently.
Steps to follow:
Step #1: Preparation Before Cleaning
Place the mower into an even or flat surface and unplug the spark plug from the mower.
Step #2: Vacant Mower Fuel Tank
Now, spread the tarp on the floor and place the mower over the tarp. Place the oil pan under the drain valve of the mower fuel tank. Remove the valve and vacant the whole tank.
Step #3: Remove The Mower Blade
Tilt the mower into its sideways and take the socket wrench to unscrew the bolts that attach the blade of the mower with the deck. Carefully remove the mower blade and keep it into a safe place.
Step #4: Use Wire Brush To Remove Grass Clippings And Dirt’s
Remove the grass clippings and dirt from the underside of the mower by scrubbing it with a wire cleaning brush.
Step #5: Spray Adequate Amount of Water
When all the dirt and debris will be cleaned, take the garden water hosepipe and strongly spray water to clean it properly.
Spray an adequate amount of water until the underside is free of dirt. Wait a while for the mower to dry fully.
Step #6: Apply Lubricant Oil and Replace The Blade
When the underside is completely dried, apply some lubricant oil in it. Now, place the blade in its previous position and tighten the bolts with the socket wrench. Refill the fuel tank with oil and reconnect the mower spark plug.
Now, your mower is absolutely ready for mowing again.
How To Clean The Underside Of A Riding Mower
To clean the underside of your riding mower, you don’t need to remove the blade of your mower. You just need a hydraulic jack to raise the mower deck above along with the other tools used for a push mower. Sounds great! Right?
So, let’s see how to clean the underside of a riding mower.
Steps to follow:
Step #1: Prepare The Riding Mower For Cleaning
Place the mower into an even surface and remove the key from the ignition switch. Unplug the spark plug from the mower also.
Step #2: Lift The Lawn Mower Upward
Place the hydraulic jack under one side of the mower deck. Press the jack handle as long as you get a suitable height to clean the bottom of the mower deck.
Step #3: Clean The Lawn Mower Underside
Now, take the wire cleaning brush and rub off the dirt and debris from the underside. After that, strongly spray water underside of the lawnmower by using the garden water hosepipe.
Wait a while for the mower to dry fully. After drying the mower completely, spray some lubricant oil underside of the mower deck.
That’s all. Now your riding mower is absolutely perfect for mowing your lawn.
Cautions
- Wear hand gloves when removing the push mower blade. Don’t touch the sharp side of the blade.
- Check the hydraulic jack carefully after raising the mower above to avoid any kind of unwanted injury.
Final verdict
In the end, cleaning the underside of a mower is not a laborious task. However, you must clean it on a regular basis if you want the superior service from your mower.
You know it’s a cinch task for you if you follow the above-mentioned process. It will also reduce your expanse if you do this at home.
Hopefully, you have a clear concept now on how to clean the underside of a lawnmower.
So, manage your time and clean it!