A lawnmower is an excellent tool that can make your life a lot easier. But to keep it in good shape, you need to know how to seat a lawn mower tire.
You see, the rim of the tire is responsible for holding it in place and keeping it inflated. However, sudden displacement can deflate your tire and ruin its productivity.
As a result, learning the correct ways to seat it becomes incredibly important to keep everything in check. That is why today, we will explain all the details that you need to know to seat your mower tires. So, let’s begin!
In this content you’ll learn:
How To Seat A Lawn Mower Tire: The Process To Follow
You need to go through certain steps to make sure that the tires are seated accurately. Each of these steps has a different purpose, and they are all equally important.
Hence, we will provide a complete breakdown of the specific words so that you don’t miss any of them. Check out the descriptions below and follow the steps sequentially.
Grab all essentials
Just like anything else, you’ll need a few tools here to carry out the process. For instance, you have to keep the tire in place while increasing the pressure in it. That is why we recommend you use stretchable ropes or straps to do the work.
Of course, you can use regular ropes. However, the stretchable ones will give you more room and flexibility. Besides, these are better for handling pressure as well.
Choosing the appropriate location is very important. One of the reasons behind this is that uneven surfaces are quite vulnerable to work on; additionally, a bumpy area might also create problems for balancing your mower. So, start by inspecting a flat area. After that, park your mower there and move on to the next step.
In this step, you will thoroughly check the tire and see if you find any signs of damage or not. The damages might vary from one another. In some cases, you might observe tiny slits along the length. Now, although they appear small, they can interrupt and prevent the inflation of the tire.
In other cases, there might be severe punctures that are easily visible. In the case where you do discover damage to the tire, you’ll need to immediately go to the hardware store and get yourself a new pair. Keep in mind that you cannot work with a damaged tire, no matter the circumstance.
Align the tire
To align the tire, we need to raise the lawnmower above ground level, and for that, we can use a tire jack. Next, we will be using the ropes or straps that we mentioned previously. So, take the rope and place one end on the outer surface of the tire.
Now, wrap it along the side and cover the entire perimeter. Finally, put a knot at the end. One thing that you should keep in mind is that the rope or strap needs to be positioned across the middle of the tire, to ensure that it doesn’t slip off during the next steps of the process.
Now, remember the knot that we had made? Well, we are going to use that to adjust the tire pressure. So, take your favorite pair of screwdrivers and start twisting them across the knot.
While you are doing that, the tension is increasing. As a result, the rope will tightly hug the tire and it will increase the pressure inside. However, make sure that you are not over-tightening the rope.
Install and fill the tire
At this point, we need to fill in the tire. A good way to do that is to use air compressors. This way, you can boost the speed and get a better result.
While you are filling in the tire, keep the pressure level in check. Note that the air is also adding up to the internal pressure. So, you should keep it in balance.
Check on the valve-system
You see, we have put in a lot of work to reach this stage, so nobody would want to lose all that progress, right?
Well, that is exactly why you need to check on the valve system. By doing this, you can make sure that everything is in place and the pressure is consistent.
Test your lawnmower
At this point, you’ve made several changes to the mower since we started this whole process. So, now, it is time to put everything back in place. You can use the same jack from before to lower the mower down. Lastly, run a final inspection and test your lawnmower to finish everything off.
Tips and Tricks
Of course, getting used to the process will take some time. However, a few tips and tricks can improve your learning curve and make things a lot smoother.
- The first tip: always check for faulty components. If you happen to notice any issues with the cables or tire beads, replace those immediately.
- The second tip: always try to avoid unnecessary risks. You can find several methods to seat a tire where people ignite the fluid to inflate the tires. Now, if you are dealing with smaller tires, these methods are completely unnecessary. Nonetheless, handle that with extreme caution if you are still using those techniques.
- Finally: let us talk about balancing the air force or PSI. As we all know, it gets quite confusing whether we are exceeding the PSI or not. Well, to avoid such situations, check the maximum PSI value of the tire beforehand. Check your tire, and you can find it on the side. In some cases, you might also need to check the manuals to get the value.
Well, that was quite fun, wasn’t it? Trust me. Learning how to seat a lawn mower tire will save you from many troubles; besides, it is time-saving and cost-effective too!
Now, we highly recommend you focus on a single step at a time to minimize the hassles. Nevertheless, if you still face any difficulties, give the entire article another thorough reading. Hopefully, it will solve all your confusion.